产品规格: | 5.5*2.1/5.5*2.5 | 产品数量: | 500.00 个 |
---|---|---|---|
包装说明: | 500个/包 | 价格说明: | 不限 |
查看人数: | 323 人 | 本页链接: | https://info.b2b168.com/s168-62239780.html |
PECIFICATION 规格书 Designation 品名: DC POWER JACK Model No. 型 号: DC-025M 1. Rating额定值: DC 30V 0.5A 2. Operation temperature range 使用温度范围: -20℃~+70℃ 3. Preservative temperature range 保存温度范围: -40℃~+85℃ 4. Construction dimension 结构尺寸: Apply to the appended drawing: 符合附加图纸 Item 项目 Test condition 测试条件 Specification规格 5. Electrical characteristics电气性能 5A Contact Resistance 接触阻抗 Being measured at 1KHz small current contact resistance meter. 在1KHZ小电流下测量. 30mΩ max. 30毫欧以下. 5B Insulation Resistance 绝缘阻抗 Measurements shall be made following application of DC 250V potential across terminals and across terminals and frame for 1 minute. 在端子之间和端子与壳之间加DC 250V条件下, 持续1分钟测量. 100MΩ min. 100兆欧以上. 5C Withstand Voltage 耐电压 AC 500V (50Hz or 60Hz) shall be applied across terminals and across terminals and frame for one minute. 在端子之间和端子与壳之间加AC 500V (50HZ或60HZ)条件下,持续1分钟测量. There shall be no breakdown. 无击穿现象出现. 6. Mechanical characteristics 机械性能 6A Insertion and Extraction force 插拔力 Being measure at across spring piece and across matching plug for ergometer. 用测力计在插头与弹片之间进行测量. Insertion and extraction force: 3~25N 插拔力: 3~25N 6B Terminal Strength 端子强度 A static force of 5N being applied in one direction on the tip of terminal for 10sec. 将5N之静负荷施加於端子**部的一个方向 持续10秒。 (1). Contact resistance:50mΩmax. 接触阻抗:50毫欧以下. (2). Insertion and withdraw force: 3~25N 插入力和拔出力:3~25N (3). Electrical characteristics and mechanical characteristics shall be satisfied. Without distinct damage. 机械,电气性能满足规定要求,无异常发生 7. Durability 耐久性 7A Soldering test 可焊性试验 The tip of the terminals shall be dipped 2mm in the solder bath at a temperature of 240±5℃ for 3±0.5sec. 端子**部被浸入焊锡池2mm深,温度240±5℃, 时间3±0.5秒。 A new uniform coating of solder shall cover a minimum of 95% of the surface being immersed. 浸入的部分95%以上表面将被锡覆盖. 7B Resistance to soldering heat 耐焊接热 The jack shall be put into at the temperature of 250±5℃ in 5±1sec(Automatic soldering) or 380±5℃ in 3±1sec(Manual soldering) after which measurement shall be made. 将产品端子浸入锡炉, 250±5℃,5±1秒 (自动焊);380±5℃,3±1秒(手工焊) (1). Contact resistance:50mΩmax. 接触阻抗:50毫欧以下. (2). Insertion and withdraw force: 3~25N 插入力和拔出力:3~25N (3). Electrical characteristics and mechanical characteristics shall be satisfied. Without distinct damage. 机械,电气性能满足规定要求,无异常发生 Remark 备 注 G-Switch 东莞品赞电子科技有限公司 SPECIFICATION 规格书 Designation 品名: DC POWER JACK Model No. 型 号: DC-025M Item 项目 Test condition 测试条件 Specification规格 7C Life test 寿命试验 5,000 cycles of operation at a rate of 20~30 cycles per minute with unloading. 无负载条件下,每分钟20~30次的速度操作5,000次。 (1). Contact resistance:50mΩmax. 接触阻抗:50毫欧以下. (2). Insertion and withdraw force: 3~25N 插入力和拔出力:3~25N (3). Electrical characteristics and mechanical characteristics shall be satisfied.Without distinct damage. 机械,电气性能满足规定要求,无异常发生 7D Heat test 耐热试验 At 85±2℃ for 96 hours, after test keep in normal condition for 30 minutes. 在85±2℃环境中放96小时,再放在正常 环境中30分钟後进行测试. (1). Contact resistance:50mΩmax. 接触电阻:50毫欧以下 (2). Insulation resistance: 50MΩmin. 绝缘电阻: 50兆欧以上 (3). There shall be no sign of damage mechanically and electrically. 无任何迹象显示机械及电器性能之损坏. 7E Humidity test. 耐湿试验 The condition of temperature 40±2℃ and humidity 90-95% for 96 hours, after test keep in normal condition for 30 minutes. 在温度40±2℃,湿度90-95%环境中放96小时, 再放在正常环境中30分钟後进行测试. 7F Cold test 耐寒试验 At –40±2℃ for 96 hours, after test keep in normal condition for 30 minutes. 在-40±2℃环境中放96小时,再置於 正常环境中30分钟後进行测试. 7G Salt spray test 喷雾试验 At 5% Nacl liquor for 24 hours, after washing, keep in normal condition for 30 minutes. 5%的Nacl溶液中喷雾24小时,用水清洗并在室 温下放置30分钟. Without excessive Corrosion or crack in appearance 表面无明显腐蚀或镀层脱落现象 8. Standard condition 试验、测定状态 Unless otherwise specified, the test and measurements shall be carried out as follows: Ambient temperature 温度: 5℃~35℃ Relative humidity 相对湿度: 45~85% Air pressure 气压:86~106kPa(860~1060mbar) However if doubt arises on the decision based on the measured values under the above-mentioned conditions, the following condition shall be employed:但在对判定産生疑义时,按下述状态实施: Ambient temperature 温度: 20±2℃ Relative humidity 相对湿度: 65±5% Air pressure 气压:86~106kPa(860~1060mbar) Remark 备 注 G-Switch 东莞品赞电子科技有限公司
相关分类: 圆形连接器 印刷板连接器 音频/视频连接器 线束 同轴连接器 条形连接器 水晶头 手机连接器 射频连接器 汽车连接器 排针 排母 矩形连接器 接线柱 接线端子 接线板 光纤连接器 电源线 电源插座 电源插头 电脑连接器 电路板连接器 电缆连接器 USB连接器
相关地区: 东莞东城 东莞南城 东莞万江 东莞莞城 东莞石碣 东莞石龙 东莞茶山 东莞石排 东莞企石 东莞横沥 东莞桥头 东莞谢岗 东莞东坑 东莞常平 东莞寮步 东莞樟木头 东莞大朗 东莞黄江 东莞清溪 东莞塘厦 东莞凤岗 东莞大岭山 东莞长安 东莞虎门 东莞厚街 东莞沙田 东莞道滘 东莞洪梅 东莞麻涌 东莞望牛墩 东莞中堂 东莞高埗 东莞松山湖